Vortech Charge Cooler

Click here for the free digital full issue.

 

 

If you’ve got a new Ecoboost Mustang, the Vortech Charge Cooler should honestly be one of the first mods you look into. Reason being: once your turbo car gets heat soaked (which could be as little as one hard pull in the summer), it’s no longer efficiently making power… and it’s more-or-less ‘game over’ until it’s had a good chance to cool. It’s a very noticeable defeat.

But this charge cooler upgrade kit from Vortech will virtually eliminate heat soak issues. And it will keep intake temperatures at a safe, stable, & performance-operational level. Also – this Vortech kit upgrades your rubber pipes to HARD pipes, giving you a more immediate & punchy boost response… with less boost response lost to rubber pipe expansion. In other words – the boost pushes through the pipes, rather that out against flexible rubber walls.

The Vortech charge cooler kit will also set the stage to support future levels of modification… and allow you to get the most out of your mods going forward. This is your Step-1. And it’s an easy install… designed to do at home. What we’ve outlined here is the general process for installation. And unlike a lot of hacked aftermarket companies out there, Vortech kits come with VERY clear & descriptive printed instructions… designed to walk you though your specific install without confusion & frustration.

STEP 1: FRONT BUMPER COVER REMOVAL

You need to remove the black plastic cover that is located above the grille & radiator. You also need to remove front under-tray panel. Both of these pieces easily come out with either clips/fasteners, or small screws. Then you need to remove the bumper bolts. There are a series of 6 bolts on the top of the bumper, 2 more on the top-sides over the headlight (under the rubber seals), and 3 plastic fasteners on the front-side of each inner fender. Pull back the fender-liner to reveal a 7mm bolt holding the bumper to the fender (one on each side). Next – pop the corners of the front bumper away from where they meet the fenders, and remove the front bumper.

STEP 2: ELECTRIC LOUVER & RADIATOR SHROUD REMOVAL

You need to remove the plastic radiator shroud and do some cutting/trimming to allow space for the larger intercooler. Don’t let that scare you. The shroud comes out with 4 easily-accessible bolts in the mid & lower section, 2 more easily accessible plastic clips on the upper section. The Vortech instruction packet will clearly show you exactly where to trim the OEM piece.

Vortech Mustang

SEE FULL DIGITAL ISSUE FOR FREE

STEP 3: OEM DISCHARGE DUCT & COOLER REMOVAL

To gain access to the discharge duct, you need to remove the factory airbox/air-filter. It’s simple – just a few 10mm screws, unplugging a plug/connector, and loosening a hose clamp. Then once that’s out of the way, disconnect the hose clamp that connects the discharge duct to the throttle body. Next – unplug the recirculation hose and the blow-off/bypass valve connector. At that point you can remove the discharge duct from the turbo. For the intercooler removal – all you have to do is loosen the hose clamps to free the hoses, remove one bolt, remove the TMAP sensor (also one bolt; and you can do it after the cooler comes out), and pull down/forward to release the intercooler from its mounting slots. Last, remove the 4 bolts holding the cross-brace just below where the intercooler was located – this will give you more clearance for the Vortech cooler.

STEP 4: VORTECH CHARGE COOLER & DISCHARGE DUCT INSTALLATION

The Vortech kit comes with a block-off plate to maintain efficient/proper airflow between the radiator, AC condenser, and the new charge cooler. Install the block-off plate, then mount the new Vortech charge cooler into place. Stand back and get excited. Then attach the OEM blow-off/bypass valve to the new piping; also re-attach the TMAP sensor to its new pipe. Run pipes, fasten clamps, reinstall airbox, check your work, reinstall bumper, & enjoy.

SEE FULL DIGITAL ISSUE FOR FREE